Whirlpool washing machine service center bangalore

The washing machine is not draining water properly.

The washing machine's drain hose was improperly installed. Please reinstall it to ensure proper drainage.

You've encountered a system error code.

To clear a code, press the Start/Pause button once. Press it again to restart the washing machine. If the issue persists, contact a Whirlpool washing machine repair technician.

The hot and cold hoses were installed incorrectly and mixed up.

First, turn off the water supply. Then, disconnect both the hot and cold water hoses and reinstall them properly. Ensure that the hot water inlet valve is connected to the hot water fitting on the washing machine, and repeat the process for the cold water inlet valve and connection. Once the hoses are correctly installed, turn the water supply back on.

The lid on your washing machine won't close.

Ensure there are no obstructions blocking the washing machine lid lock. Then, clean the contacts using a cotton swab dipped in medical alcohol, as dirty contacts may hinder proper connection.

The lid remains closed

The washing machine has detected objects on the lid preventing it from unlocking. Please remove any objects from the lid.

The washing machine isn't receiving sufficient water to launder the clothes.

First, verify that the intake valves are completely open. Then, examine the intake hoses to ensure they are not twisted, bent, or impaired. Lastly, confirm that you have installed anti-flood hoses and controls on the water line leading to the washing machine.

The washing machine lid has been left ajar.

Shut the cover to clear the display. If the lid remains open for over 10 minutes, the cycle will reset, and the washing machine will drain the water. Restart the wash cycle if the water drains. Do not add extra detergent as your clothes are already saturated with water and detergent.

Your washing machine is not balanced.

If the washer is performing load balancing, allow it to finish the process. Otherwise, if the washing machine has stopped, you can open the lid to redistribute the load. Then, press "Start" to resume the cycle.

The washing machine has been overloaded, causing the cycle to halt and the water and detergent to drain.

To decrease the load size, take out several items from the washing machine. Afterwards, add detergent to the machine and press the Start/Pause button.

The wash cycle was interrupted due to a power failure.

Press and hold the start button to initiate the wash cycle again, or press the power button to reset the display.

There is excessive foam in the washing machine, likely due to either using too much washing powder or low-quality detergent.

Eliminate excess suds by running multiple empty wash cycles to rinse them out. Alternatively, you can add a small amount of plain vinegar to remove soap residue. To prevent excessive suds in the future, ensure you use high-quality detergents or liquid detergents and follow the recommended dosage for your washing machine.

Control lock is activated.

Press the control lock button. You may need to identify which button activates the control lock, as different machines may use different buttons. If you're using an older machine, you might need to press and hold the control lock button.

The washing machine is unable to detect the detergent cartridge.

Ensure the detergent cartridge is properly installed and that the detergent compartment is fully closed.

The wash cycle was interrupted or cancelled.

The error code will be visible for 20-30 minutes, during which the washing machine may pause to drain the water. To clear the error code, press the pause/cancel button twice and the power button once. If this doesn't resolve the issue, unplug the washing machine for 1 minute.

There's an excessive amount of foam in your washing machine drum.

Resolve the issue by running multiple empty wash cycles to eliminate the excess suds from the washing machine. Additionally, you can add 1 cup of vinegar to your wash cycle, which helps in removing soap residue. Ensure a long-term solution by using only high-quality detergent or liquid detergent in your washing machine.

The washing machine door refuses to shut.

Inspect the washing machine door to identify any obstructions preventing it from closing properly. If necessary, use a cotton swab dipped in medical alcohol to clean the contacts of the locking mechanism, as dirt buildup can hinder the door's operation.

Press the pause/cancel button twice and then press the power button once. This will clear the code.

Engine speed problem.

If you have a new machine, ensure that the shipping bolts have been removed. Otherwise, you may have overloaded the washing machine.

Press the pause/cancel button twice and then press the power button once. This will clear the code.

The washing machine identifies a low water flow into the machine.

Examine the intake valves to ensure they are turned on and fully open. Additionally, inspect the intake hoses to ensure they are not twisted, bent, or damaged. Lastly, verify that you have not utilized flood protection hoses and controls on the water line connected to the washing machine.

Then press the pause/cancel button twice and the power button once to reset the error code.

Problem with the dispenser system.

Ensure that the dispenser system is free from clogs. You might need to take out the dispenser box and clean it in the sink using mild soap and warm water.

Long drain time.

Make sure the drain hose is not kinked or clogged.

There is another type of error.

If you encounter any other F-codes or E-codes, disconnect the washing machine from the power source for 1 minute before reconnecting it. Then, select your cycle and start it again. If the error code appears a second time, contact a Whirlpool washing machine repair technician.