LG washing machine service center bangalore

The washing machine does not drain water

• Unplug the washing machine.
• Use the emergency drain, inspect the drain filter and, if necessary, clean it.
• Connect the power and turn on the Rinse+Spin mode in the machine.
• If the error does not appear, it was a clogged drain filter, and you can continue washing.

If the error occurs again, check if there is a blockage in the drain - start the machine with free flow of water:

• Unplug the washing machine from the outlet.
• Disconnect the drain hose from the sewer (siphon, pipe). Also check the extension points of the hose, if it was extended when connecting.
• Place the end of the drain hose into the bathtub or sink and check for kinks.
• Turn on the machine and run the Rinse+Spin mode (without laundry and powder).
• If the water has drained, there may be a clog in the drain. Clean it and connect the drain hose to the sewer.
• If the error occurs again, contact the service center.

The hatch is not closed

• Turn off the power.
• Make sure that the closing of the hatch is not obstructed by foreign objects (for example, pieces of clothing).
• Inspect the symmetry of the hatch fastenings (sometimes this is a sign of a faulty lock).
• Inspect the cuffs for deformation and the door for proper fastenings.
• If there are deformations, fix them yourself or invite a repairman.

Water does not heat up

Most often, the problem of heating water (washing in cold water) or, on the contrary, its excessive heating, occurs due to a malfunction of the heating element - the heating element of the washing machine. Self-repair without sufficient knowledge often leads to additional equipment defects and increases the cost of repairs. Seek help from qualified professionals.

The washing machine does not fill with water

It happens that, regardless of the choice of washing mode, the process itself does not start. What could it be:

• The hatch is not closed tightly, which prevents the program from starting.
• UBL malfunction.
• There is no water in the system.
• Kink in the water intake hose.
• Violations in the blocker (electrical circuit).

In the latter case, it is better to contact a specialist.

Overflow of water

• Overflow of water in washing machines can occur for the following reasons:
• Malfunction of the pressure control sensor (press stat).
• Failure of the filling valve (FV).
• The electronic control module is malfunctioning.

If this type of breakdown occurs, you should immediately call a specialist.

Depending on the nature of the breakdown, you can either repair it yourself or invite specialists. But in this particular case, it is better to resort to the help of professionals.

Self-help measures:

• Try to normalize the position of the hoses, install the washing machine correctly, maintaining balance.
• Check and replace the failed part.

Faulty heating element, problems with water heating

A heating element is a part of a washing machine that provides heating of water during washing (or drying clothes in those machines where such a function is provided). Consequently, when it fails, the degree of heating of the water suffers, ranging from complete failure of operation to overheating.

Since this part is high-tech in its design, it is wiser to fix this malfunction with the help of specialists.

To accurately diagnose a breakdown, you will need a tester, and to make a decision about completely replacing the heating element or repairing the old one, you will need a well-qualified technician.

The drum does not rotate, its rotation speed is impaired, it is positioned incorrectly

There may be several reasons for this, from complete failure of the engine, electronic unit, to incorrect installation or failure of bearings.

First, make sure that the shipping bolts are not left behind during installation.

If no obvious causes of the breakdown have been identified, then it is better to contact a technician, since the problem may require professional diagnostics with special equipment, and repair may require disassembling the washing machine.

The drum does not rotate, its rotation speed is impaired, it is positioned incorrectly

There may be several reasons for this, from complete failure of the engine, electronic unit, to incorrect installation or failure of bearings.

First, make sure that the shipping bolts are not left behind during installation.

If no obvious causes of the breakdown have been identified, then it is better to contact a technician, since the problem may require professional diagnostics with special equipment, and repair may require disassembling the washing machine.

Water leak

Water leaking into the washing machine tray is a fairly common problem. It may have several reasons.

• Failure of the float sensor.
• The tank has become depressurized.
• Violation of the integrity of the rubber cuff of the hatch.
• The integrity of the hoses (drain and water intake), pipes, etc. is damaged.

Therefore, first of all, you need to make sure that there is no deformation of the hoses, that they are connected correctly, and that the tank is intact.

If you are unable to resolve the problem yourself, contact the service center.